[srslte-users] PDCCH MISS being too High with PDSCH transmission

Fri Feb 9 16:56:30 UTC 2018

Hello Justin,

Thanks a lot for the quick response.

By default the mbsfn_subframe - sf_type is set to "true" on initialization (pdsch_enodeb).

I have set it to false and used the frequencies suggested by you and the behaviour is as below:

I could see some improvement where the PDCCH-Miss now shows up to 80%, a decrease ~20% from previous tests.

Just for information, what should be the ideal PDCCH decode failure rate in these radio conditions and what power levels should be set?

Again, appreciate your help.

BR,
Sandeep

________________________________
From: Justin Tallon <justin.tallon at softwareradiosystems.com>
Sent: Friday, February 9, 2018 9:41:19 PM
To: Sandeep Sarma -ERS, HCL Tech
Cc: srslte-users at lists.softwareradiosystems.com; Sriram P; Jagadish Rajanna; Nazia Shaik
Subject: Re: [srslte-users] PDCCH MISS being too High with PDSCH transmission

Hey Sandeep!

I see in the logs "Sandy setting mbsfn_subframe to true"

Are setting this value to True?

Can you try to receive a commercial cell with the pdsch_ue to see if you can see a reasonable signal?

try 806000000 or 816000000.

Thanks,
Justin

____
Justin Tallon Ph.D.

Software Radio Systems (SRS)
http://www.softwareradiosystems.com<https://apac01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.softwareradiosystems.com%2F&data=02%7C01%7Csandeep-s%40hcl.com%7Cf8fb5838bccc4f5a6c6908d56fd7cf4c%7Cdd85efd06a9c4fee843ed525fa4be3ca%7C0%7C0%7C636537895051230445&sdata=PCuP8RCLXrDpdQ%2B5vi%2Bj%2F%2FcQ1ipel%2BjatupFHBLDFm4%3D&reserved=0>

+353-86-067-0753 | justin.tallon at softwareradiosystems.com<mailto:justin.tallon at softwareradiosystems.com>

On Fri, Feb 9, 2018 at 2:32 PM, Sandeep Sarma -ERS, HCL Tech <sandeep-s at hcl.com<mailto:sandeep-s at hcl.com>> wrote:

Hello srsLTE Users,

I have a test setup with 2 USRP B210 SDRs and a wired RF cable between Tx and Rx antenna ports.

While I run the pdsch_enb and pdsch_ue example scripts, I see a lot of DCI miss through PDCCH-Miss % being around 90-98%.

Tx_gain, clock rate is default and I have a 30DB attenuator at the pdsch_ue (USRP Rrx side).

Below are the commands and verbose logs are attached.

pdsch_enb:

./pdsch_enodeb -f 5200000000 -m 11 -p 50 -v -n 5000

pdsch_ue:

./pdsch_ue -f 5200000000 -r 1234 -v

I've also tried with increasing the tx_gain and mcs but situation is same.

Appreciate if I can hear from anyone on how to improve the decoding at the receiving end. It would help tremendously.

BR,

Sandeep

::DISCLAIMER::
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
The contents of this e-mail and any attachment(s) are confidential and intended for the named recipient(s) only. E-mail transmission is not guaranteed to be secure or error-free as information could be intercepted, corrupted, lost, destroyed, arrive late or incomplete, or may contain viruses in transmission. The e mail and its contents (with or without referred errors) shall therefore not attach any liability on the originator or HCL or its affiliates. Views or opinions, if any, presented in this email are solely those of the author and may not necessarily reflect the views or opinions of HCL or its affiliates. Any form of reproduction, dissemination, copying, disclosure, modification, distribution and / or publication of this message without the prior written consent of authorized representative of HCL is strictly prohibited. If you have received this email in error please delete it and notify the sender immediately. Before opening any email and/or attachments, please check them for viruses and other defects.
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

_______________________________________________
srslte-users mailing list
srslte-users at lists.softwareradiosystems.com<mailto:srslte-users at lists.softwareradiosystems.com>
http://www.softwareradiosystems.com/mailman/listinfo/srslte-users<https://apac01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.softwareradiosystems.com%2Fmailman%2Flistinfo%2Fsrslte-users&data=02%7C01%7Csandeep-s%40hcl.com%7Cf8fb5838bccc4f5a6c6908d56fd7cf4c%7Cdd85efd06a9c4fee843ed525fa4be3ca%7C0%7C0%7C636537895051230445&sdata=OxLB6rESevvWY6ECYd%2FMgqUn6DbXmF1zG%2FYb%2Fb6nA6k%3D&reserved=0>

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://lists.srsran.com/pipermail/srsran-users/attachments/20180209/f47b7161/attachment.htm>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: pdsch_enb_ue_806_original.tar.gz
Type: application/gzip
Size: 343427 bytes
Desc: pdsch_enb_ue_806_original.tar.gz
URL: <https://lists.srsran.com/pipermail/srsran-users/attachments/20180209/f47b7161/attachment.gz>