[srslte-users] Connection between commercial ue and LimeSdr

[lilijobo1]

Hello,

at the moment I try to get a connection between my LimeSdr and my galaxy
s5 with a programmed simcard. I programmed the simcard with the values
given in the user_db.csv . Is there a way to check if the simcard is
properly programmed? When I run srsepc and srsenb I get the output
mentioned below but nothing more happens.  Secondly I would like to know
if I have to specify manually which channels to be used for rx and tx
and if yes how do I do it?

Thank you in advance




Johannes

--->srsepc<---

Built in Release mode using commit 429ee901 on branch master.


---  Software Radio Systems EPC  ---

Reading configuration file /home/localadmin/.config/srslte/epc.conf...
HSS Initialized.
MME GTP-C Initialized
MME Initialized. MCC: 0xf001, MNC: 0xff01
SP-GW Initialized.
Received S1 Setup Request.
S1 Setup Request - eNB Name: srsenb01, eNB id: 0x19b
S1 Setup Request - MCC:001, MNC:01, PLMN: 61712
S1 Setup Request - TAC 7, B-PLMN 0
S1 Setup Request - Paging DRX 2
Sending S1 Setup Response




--->srsenb<---

Built in Release mode using commit 429ee901 on branch master.

---  Software Radio Systems LTE eNodeB  ---

Reading configuration file /home/localadmin/.config/srslte/enb.conf...
Soapy has found device #0: addr=1d50:6108, driver=lime,
label=LimeSDR-USB [USB 3.0] 907060244302D, media=USB 3.0, module=FX3,
name=LimeSDR-USB, serial=000907060244302D,
[INFO] Make connection: 'LimeSDR-USB [USB 3.0] 907060244302D'
[INFO] Reference clock 30.72 MHz
[INFO] Device name: LimeSDR-USB
[INFO] Reference: 30.72 MHz
[INFO] LMS7002M calibration values caching Disable
[INFO] RX LPF configured
Set Rx bandwidth to 2.50 MHz
[INFO] Filter calibrated. Filter order-4th, filter bandwidth set to 5
MHz.Real pole 1st order filter set to 2.5 MHz. Preemphasis filter not active
[INFO] TX LPF configured
Set Tx bandwidth to 5.00 MHz
Setting up RX stream
Setting up TX stream
Available device sensors:
  - clock_locked
  - lms7_temp
Available sensors for RX channel 0:
  - lo_locked

[INFO] Tx calibration finished

[INFO] Rx calibration finished
State of gain elements for Rx channel 0 (AGC not supported):
  - TIA: 9.00 dB
  - LNA: 30.00 dB
  - PGA: -4.00 dB
State of gain elements for Tx channel 0 (AGC not supported):
  - TIA: 9.00 dB
  - LNA: 30.00 dB
  - PGA: -4.00 dB
Rx antenna set to LNAL
Tx antenna set to BAND1

Warning burst preamble is not calibrated for device lime. Set a value
manually

Setting frequency: DL=880.0 Mhz, UL=835.0 MHz
Tuned Tx to 880.00 MHz
Tuned Rx to 835.00 MHz
Set master clock rate to 11.52 MHz
Setting Sampling frequency 11.52 MHz
[INFO] RX LPF configured
Set Rx bandwidth to 8.64 MHz
[INFO] Filter calibrated. Filter order-4th, filter bandwidth set to 8.64
MHz.Real pole 1st order filter set to 2.5 MHz. Preemphasis filter not active
[INFO] TX LPF configured
Set Tx bandwidth to 8.64 MHz

==== eNodeB started ===
Type <t> to view trace
[INFO] Tx calibration finished
[INFO] Rx calibration finished
[WARNING] L