[srslte-users] srsue doesn't sync with our local commercial eNb (Nokia)
Guillaume
ggballet at gmail.com
Fri Oct 18 13:26:12 UTC 2019
Hello list,
We have trouble attaching srsue to the LTE network we run.
Apparently srsue doesn't sync with our eNb. (B28b, bw 3Mhz, PLMN 208180,
P 30dB)
Environment; Linux 64bits, bladeRF, usb3, Intel(R) Core(TM) i7-7700K CPU
@ 4.20GHz, NVMe SSD, 64GB ram
Has someone a clue?
---------------------------
$ lsb_release -a
LSB Version:
core-9.20170808ubuntu1-noarch:printing-9.20170808ubuntu1-noarch:security-9.20170808ubuntu1-noarch
Distributor ID: Ubuntu
Description: Ubuntu 18.04.3 LTS
Release: 18.04
Codename: bionic
$ uname -a
Linux clevo.gigi.edu 4.13.0-16-generic #19-Ubuntu SMP Wed Oct 11
18:35:14 UTC 2017 x86_64 x86_64 x86_64 GNU/Linux
$ free
total utilisé libre partagé tamp/cache
disponible
Mem: 65797284 4492132 34195000 100048 27110152 60471388
Partition d'échange: 0 0 0
$ bladeRF-cli -i
bladeRF> print
RX1 Bandwidth: 3840000 Hz
TX1 Bandwidth: 3840000 Hz
RX1 Frequency: 789500000 Hz
TX1 Frequency: 734500000 Hz
RX1 AGC: Disabled
GPIO: 0x001b0057
LMS Enable: Enabled
LMS RX Enable: Enabled
LMS TX Enable: Enabled
TX Band: Low Band (300M - 1.5GHz)
RX Band: Low Band (300M - 1.5GHz)
RX Source: Baseband
Loopback mode: none
RX mux: BASEBAND - Baseband samples
Gain RX1 overall: 6 dB (Range: [-1, 60])
lna: 3 dB (Range: [0, 6])
rxvga1: 9 dB (Range: [5, 30])
rxvga2: 0 dB (Range: [0, 30])
Gain TX1 overall: 73 dB (Range: [17, 73])
txvga1: -4 dB (Range: [-35, -4])
txvga2: 25 dB (Range: [0, 25])
Sampling: Internal
RX1 sample rate: 3840000 0/1
TX1 sample rate: 3840000 0/1
SMB Mode: Disabled
Current VCTCXO trim: 0x8e50
Stored VCTCXO trim: 0x8e50
VCTCXO tamer mode: Disabled
Expansion GPIO register: 0xffeafb7f
Expansion GPIO direction register: 0x004506f0
Hardware status:
RF routing:
TX: auto
RX: lna1
bladeRF> ver
bladeRF-cli version: 1.6.1-git-c9a2230c
libbladeRF version: 2.0.2-git-c9a2230c
Firmware version: 2.0.0
FPGA version: 0.8.0
$ cat ~/.config/srslte/ue.conf
#####################################################################
# srsUE configuration file
#####################################################################
#####################################################################
# RF configuration
#
# dl_earfcn: Downlink EARFCN code.
# freq_offset: Uplink and Downlink optional frequency offset (in Hz)
# tx_gain: Transmit gain (dB).
# rx_gain: Optional receive gain (dB). If disabled, AGC if enabled
#
# Optional parameters:
# dl_freq: Override DL frequency corresponding to dl_earfcn
# ul_freq: Override UL frequency corresponding to dl_earfcn
# nof_radios: Number of available RF devices
# nof_rf_channels: Number of RF channels per radio
# nof_rx_ant: Number of RX antennas per channel
# device_name: Device driver family. Supported options: "auto"
(uses first found), "UHD" or "bladeRF"
# device_args: Arguments for the device driver. Options are
"auto" or any string.
# Default for UHD:
"recv_frame_size=9232,send_frame_size=9232"
# Default for bladeRF: ""
# device_args_2: Arguments for the RF device driver 2.
# device_args_3: Arguments for the RF device driver 3.
# time_adv_nsamples: Transmission time advance (in number of samples)
to compensate for RF delay
# from antenna to timestamp insertion.
# Default "auto". B210 USRP: 100 samples, bladeRF: 27.
# burst_preamble_us: Preamble length to transmit before start of burst.
# Default "auto". B210 USRP: 400 us, bladeRF: 0 us.
# continuous_tx: Transmit samples continuously to the radio or on
bursts (auto/yes/no).
# Default is auto (yes for UHD, no for rest)
#####################################################################
[rf]
dl_earfcn = 9525
#freq_offset = 0
tx_gain = 100
#rx_gain = 40
#nof_radios = 1
nof_rx_ant = 1
# For best performance in 2x2 MIMO and >= 15 MHz use the following
device_args settings:
# USRP B210: pass num_recv_frames=64,num_send_frames=64
device_name = bladeRF
device_args = auto
time_adv_nsamples = auto
burst_preamble_us = auto
continuous_tx = auto
#####################################################################
# Packet capture configuration
#
# Packet capture is supported at both MAC and NAS layers.
# MAC-layer packets are captured to file in the compact format
# decoded by the Wireshark mac-lte-framed dissector.
# To use this dissector, edit the preferences for DLT_USER to
# add an entry with DLT=147, Payload Protocol=mac-lte-framed.
# For more information see: https://wiki.wireshark.org/MAC-LTE
# NAS-layer packets are dissected with DLT=148, and
# Payload Protocol = nas-eps.
#
# enable: Enable MAC layer packet captures (true/false)
# filename: File path to use for MAC packet captures
# nas_enable: Enable NAS layer packet captures (true/false)
# nas_filename: File path to use for NAS packet captures
#####################################################################
[pcap]
enable = true
filename = /tmp/ue.pcap
nas_enable = true
nas_filename = /tmp/nas.pcap
#####################################################################
# Log configuration
#
# Log levels can be set for individual layers. "all_level" sets log
# level for all layers unless otherwise configured.
# Format: e.g. phy_level = info
#
# In the same way, packet hex dumps can be limited for each level.
# "all_hex_limit" sets the hex limit for all layers unless otherwise
# configured.
# Format: e.g. phy_hex_limit = 32
#
# Logging layers: rf, phy, mac, rlc, pdcp, rrc, nas, gw, usim, all
# Logging levels: debug, info, warning, error, none
#
# filename: File path to use for log output. Can be set to stdout
# to print logs to standard output
# file_max_size: Maximum file size (in kilobytes). When passed, multiple
files are created.
# If set to negative, a single log file will be created.
#####################################################################
[log]
all_level = info
phy_lib_level = info
all_hex_limit = 32
filename = /tmp/ue.log
file_max_size = -1
#####################################################################
# USIM configuration
#
# mode: USIM mode (soft/pcsc)
# algo: Authentication algorithm (xor/milenage)
# op/opc: 128-bit Operator Variant Algorithm Configuration Field (hex)
# - Specify either op or opc (only used in milenage)
# k: 128-bit subscriber key (hex)
# imsi: 15 digit International Mobile Subscriber Identity
# imei: 15 digit International Mobile Station Equipment Identity
# pin: PIN in case real SIM card is used
# reader: Specify card reader by it's name as listed by 'pcsc_scan'. If
empty, try all available readers.
#####################################################################
[usim]
mode = pcsc
#algo = milenage
#opc =
#k =
#imsi =
imei = 353490069873319
#reader =
#pin = 1234
#####################################################################
# RRC configuration
#
# ue_category: Sets UE category (range 1-5). Default: 4
# release: UE Release (8 to 10)
# feature_group: Hex value of the featureGroupIndicators field in the
# UECapabilityInformation message. Default 0xe6041000
# mbms_service_id: MBMS service id for autostarting MBMS reception
# (default -1 means disabled)
# mbms_service_port: Port of the MBMS service
#####################################################################
[rrc]
ue_category = 5
release = 10
#feature_group = 0xe6041000
#mbms_service_id = -1
#mbms_service_port = 4321
#####################################################################
# NAS configuration
#
# apn: Set Access Point Name (APN)
# apn_protocol: Set APN protocol (IPv4, IPv6 or IPv4v6.)
# user: Username for CHAP authentication
# pass: Password for CHAP authentication
# force_imsi_attach: Whether to always perform an IMSI attach
# eia: List of integrity algorithms included in UE
capabilities
# Supported: 1 - Snow3G, 2 - AES
# eea: List of ciphering algorithms included in UE
capabilities
# Supported: 0 - NULL, 1 - Snow3G, 2 - AES
#####################################################################
[nas]
apn = srsapn
apn_protocol = ipv4
#user = srsuser
#pass = srspass
force_imsi_attach = true
eia = 1,2
eea = 0,1,2
#####################################################################
# GW configuration
#
# ip_devname: Name of the tun_srsue device. Default: tun_srsue
# ip_netmask: Netmask of the tun_srsue device. Default:
255.255.255.0
#####################################################################
[gw]
ip_devname = tun_srsue
ip_netmask = 255.255.255.0
#####################################################################
# GUI configuration
#
# Simple GUI displaying PDSCH constellation and channel freq response.
# (Requires building with srsGUI)
# enable: Enable the graphical interface (true/false)
#####################################################################
[gui]
enable = true
#####################################################################
# Channel emulator options:
# dl.enable: Enable/Disable internal Downlink channel emulator
#
# -- Fading emulator
# dl.fading.enable: Enable/disable fading simulator
# dl.fading.model: Fading model + maximum doppler (E.g. none, epa5,
eva70, etu300, etc)
#
# -- Delay Emulator delay(t) = delay_min + (delay_max - delay_min) *
(1 + sin(2pi*t/period)) / 2
# Maximum speed [m/s]: (delay_max - delay_min) *
pi * 300 / period
# dl.delay.enable: Enable/disable delay simulator
# dl.delay.period: Delay period in seconds (integer).
# dl.delay.maximum_us: Maximum delay in microseconds
# dl.delay.minumum_us: Minimum delay in microseconds
#
# -- Radio-Link Failure (RLF) Emulator
# dl.rlf.enable: Enable/disable RLF simulator
# dl.rlf.t_on_ms: Time for On state of the channel (ms)
# dl.rlf.t_off_ms: Time for Off state of the channel (ms)
#####################################################################
[channel]
#dl.enable = false
#dl.fading.enable = false
#dl.fading.model = none
#dl.delay.enable = false
#dl.delay.period = 3600
#dl.delay.maximum_us = 100
#dl.delay.minimum_us = 10
#dl.rlf.enable = false
#dl.rlf.t_on_ms = 10000
#dl.rlf.t_off_ms = 2000
#ul.enable = false
#ul.fading.enable = false
#ul.fading.model = none
#ul.delay.enable = false
#ul.delay.period = 3600
#ul.delay.maximum_us = 100
#ul.delay.minimum_us = 10
#ul.rlf.enable = false
#ul.rlf.t_on_ms = 10000
#ul.rlf.t_off_ms = 2000
#####################################################################
# PHY configuration options
#
# rx_gain_offset: RX Gain offset to add to rx_gain to calibrate
RSRP readings
# prach_gain: PRACH gain (dB). If defined, forces a gain for
the tranmsission of PRACH only.,
# Default is to use tx_gain in [rf] section.
# cqi_max: Upper bound on the maximum CQI to be reported.
Default 15.
# cqi_fixed: Fixes the reported CQI to a constant value.
Default disabled.
# snr_ema_coeff: Sets the SNR exponential moving average
coefficient (Default 0.1)
# snr_estim_alg: Sets the noise estimation algorithm. (Default refs)
# Options: pss: use difference between
received and known pss signal,
# refs: use difference between noise
references and noiseless (after filtering)
# empty: use empty subcarriers in the
boarder of pss/sss signal
# pdsch_max_its: Maximum number of turbo decoder iterations
(Default 4)
# nof_phy_threads: Selects the number of PHY threads (maximum 4,
minimum 1, default 2)
# equalizer_mode: Selects equalizer mode. Valid modes are: "mmse",
"zf" or any
# non-negative real number to indicate a
regularized zf coefficient.
# Default is MMSE.
# sfo_ema: EMA coefficient to average sample offsets used
to compute SFO
# sfo_correct_period: Period in ms to correct sample time to adjust
for SFO
# sss_algorithm: Selects the SSS estimation algorithm. Can choose
between
# {full, partial, diff}.
# estimator_fil_auto: The channel estimator smooths the channel
estimate with an adaptative filter.
# estimator_fil_stddev: Sets the channel estimator smooth gaussian
filter standard deviation.
# estimator_fil_order: Sets the channel estimator smooth gaussian
filter order (even values perform better).
# The taps are [w, 1-2w, w]
#
# snr_to_cqi_offset: Sets an offset in the SNR to CQI table. This is
used to adjust the reported CQI.
#
# pregenerate_signals: Pregenerate uplink signals after attach.
Improves CPU performance.
#
# interpolate_subframe_enabled: Interpolates in the time domain the
channel estimates within 1 subframe. Default is to average.
#
# sic_pss_enabled: Applies Successive Interference Cancellation to
PSS signals when searching for neighbour cells.
# Must be disabled if cells have identical channel
and timing, for instance if generated from
# the same source.
#
# pdsch_csi_enabled: Stores the Channel State Information and uses
it for weightening the softbits. It is only
# used in TM1. It is True by default.
#
# pdsch_8bit_decoder: Use 8-bit for LLR representation and turbo
decoder trellis computation (Experimental)
# force_ul_amplitude: Forces the peak amplitude in the PUCCH, PUSCH
and SRS (set 0.0 to 1.0, set to 0 or negative for disabling)
#
#####################################################################
[phy]
#rx_gain_offset = 62
#prach_gain = 30
#cqi_max = 15
#cqi_fixed = 10
#snr_ema_coeff = 0.1
#snr_estim_alg = refs
#pdsch_max_its = 8 # These are half iterations
#nof_phy_threads = 3
#equalizer_mode = mmse
#sfo_ema = 0.1
#sfo_correct_period = 10
#sss_algorithm = full
#estimator_fil_auto = false
#estimator_fil_stddev = 1.0
#estimator_fil_order = 4
#snr_to_cqi_offset = 0.0
#interpolate_subframe_enabled = false
#sic_pss_enabled = true
#pregenerate_signals = false
#pdsch_csi_enabled = true
#pdsch_8bit_decoder = false
#force_ul_amplitude = 0
#####################################################################
# General configuration options
#
# metrics_csv_enable: Write UE metrics to CSV file.
#
# metrics_period_secs: Sets the period at which metrics are requested
from the UE.
#
# metrics_csv_filename: File path to use for CSV metrics.
#
#####################################################################
[general]
metrics_csv_enable = true
metrics_period_secs = 1
metrics_csv_filename = /tmp/ue_metrics.csv
$ sudo /usr/local/bin/srsue -v
Version 19.6.0
$ sudo /usr/local/bin/srsue
Reading configuration file /home/gigi/.config/srslte/ue.conf...
Built in Release mode using commit c4bcd6e2 on branch master.
Opening 1 RF devices with 1 RF channels...
Opening bladeRF...
Set RX sampling rate 1.92 Mhz, filter BW: 2.50 Mhz
Waiting PHY to initialize ... done!
Attaching UE...
Searching cell in DL EARFCN=9525, f_dl=789.5 MHz, f_ul=734.5 MHz
set RX frequency to 789500000
set TX frequency to 734500000
Set RX sampling rate 1.92 Mhz, filter BW: 2.50 Mhz
.
Found Cell: Mode=FDD, PCI=1, PRB=15, Ports=2, CFO=-0.0 KHz
Set RX sampling rate 3.84 Mhz, filter BW: 3.84 Mhz
SYNC: Receiving from radio while in IDLE_RX
SYNC: Receiving from radio while in IDLE_RX
Set RX sampling rate 1.92 Mhz, filter BW: 2.50 Mhz
.
Found Cell: Mode=FDD, PCI=1, PRB=15, Ports=2, CFO=-0.1 KHz
Set RX sampling rate 3.84 Mhz, filter BW: 3.84 Mhz
SYNC: Receiving from radio while in IDLE_RX
SYNC: Receiving from radio while in IDLE_RX
Set RX sampling rate 1.92 Mhz, filter BW: 2.50 Mhz
.
Found Cell: Mode=FDD, PCI=1, PRB=15, Ports=2, CFO=0.0 KHz
Set RX sampling rate 3.84 Mhz, filter BW: 3.84 Mhz
^CStopping srsUE... Press Ctrl+C 9 more times to force stop
SYNC: Receiving from radio while in IDLE_RX
Saving MAC PCAP file
Saving NAS PCAP file
SYNC: Receiving from radio while in IDLE_RX
--- exiting ---
$cat /tmp/ue.log
12:28:28.252322 [UE ] [I] Built in Release mode using commit c4bcd6e2
on branch master.
12:28:28.527424 [PHY0] [I] [00000] Init PDCCH: Max bits: 7920
12:28:28.527515 [PHY0] [I] [00000] Init PDSCH: 110 PRBs, max_symbols: 18480
12:28:28.634870 [USIM] [I] Available Card Reader: OMNIKEY AG Smart Card
Reader 00 00
12:28:28.634889 [USIM] [I] Trying Card Reader: OMNIKEY AG Smart Card
Reader 00 00
12:28:28.642237 [PHY0] [I] [00000] Init PMCH: 110 PRBs, max_symbols: 15840
12:28:28.645570 [USIM] [I] Card=0x316ce793 active_protocol=1 (T0)
12:28:28.663391 [PHY0] [I] [00000] Init PUSCH: 110 PRBs
12:28:28.687887 [PHY0] [I] [00000] Init PDCCH: Max bits: 7920
12:28:28.687973 [PHY0] [I] [00000] Init PDSCH: 110 PRBs, max_symbols: 18480
12:28:28.708984 [PHY0] [I] [00000] Init PMCH: 110 PRBs, max_symbols: 15840
12:28:28.730379 [PHY0] [I] [00000] Init PUSCH: 110 PRBs
12:28:28.754626 [PHY0] [I] [00000] Init PDCCH: Max bits: 7920
12:28:28.754711 [PHY0] [I] [00000] Init PDSCH: 110 PRBs, max_symbols: 18480
12:28:28.769719 [USIM] [I] USIM is supported
12:28:28.775909 [PHY0] [I] [00000] Init PMCH: 110 PRBs, max_symbols: 15840
12:28:28.797280 [PHY0] [I] [00000] Init PUSCH: 110 PRBs
12:28:28.825746 [PHY0] [I] [00000] Init PDCCH: Max bits: 7920
12:28:28.825834 [PHY0] [I] [00000] Init PDSCH: 110 PRBs, max_symbols: 18480
12:28:28.846846 [PHY0] [I] [00000] Init PMCH: 110 PRBs, max_symbols: 15840
12:28:28.855349 [MAC ] [I] [00000] Resetting MAC
12:28:28.856732 [MAC ] [I] [00000] Logical Channel Setup: LCID=0, LCG=0,
priority=0, PBR=-1, BSD=50ms, bucket_size=0
12:28:28.856749 [MAC ] [I] [00000] Logical Channel Setup: LCID=1, LCG=0,
priority=1, PBR=-1, BSD=50ms, bucket_size=0
12:28:28.856760 [RLC ] [I] Added radio bearer SRB0 in Transparent Mode
12:28:28.856763 [RLC ] [I] Configured radio bearer SRB0 in Transparent Mode
12:28:28.872141 [USIM] [I] Read Home PLMN Id=208180
12:28:28.872168 [NAS ] [I] Skip reading context from file.
12:28:28.872183 [RRC ] [I] Set PDSCH-Config p_a=dB0
12:28:28.872186 [RRC ] [I] Set MAC default configuration
12:28:28.872189 [MAC ] [I] [00000] BSR: Configured timer reTX 2560 ms
12:28:28.872193 [RRC ] [I] Set MAC main config: harq-MaxReTX=5,
bsr-TimerReTX=2560, bsr-TimerPeriodic=-1
12:28:28.872198 [RRC ] [I] using srand seed of 872197
12:28:28.880633 [MAC ] [I] [00000] DL retx: 0.00 %, perpkt: 0.00, UL
retx: 0.00 % perpkt: 0.00
12:28:28.880656 [RLC ] [I] LCID=0, RX throughput: 0.000000 Mbps. TX
throughput: 0.000000 Mbps.
12:28:28.880660 [GW ] [I] RX throughput: 0.000000 Mbps. TX throughput:
0.000000 Mbps.
12:28:28.880894 [NAS ] [I] Attach Request
12:28:28.880903 [NAS ] [I] No PLMN selected. Starting PLMN Search...
12:28:28.880906 [RRC ] [I] Starting PLMN search
12:28:28.880910 [PHY0] [I] [00000] Cell Search: Start EARFCN index=0/1
12:28:28.883627 [PHY0] [I] [00001] Cell Search: changing frequency to
EARFCN=9525
12:28:28.883648 [PHY0] [I] [00001] SYNC: Set DL EARFCN=9525, f_dl=789.5
MHz, f_ul=734.5 MHz
12:28:28.888645 [PHY0] [I] [00005] Cell Search: Setting Cell search state
12:28:28.900490 [PHY0] [I] [00006] SYNC: Setting Cell Search sampling rate
12:28:28.900509 [PHY0] [I] [00006] SYNC: Searching for cell...
12:28:28.900780 [PHY0] [I] [00006] CP-CFO: estimated=0.006646,
mean=0.006646
12:28:28.900994 [PHY0] [I] [00006] PSS: id=0, peak_pos=845,
peak_value=1.040582
12:28:28.900998 [PHY0] [I] [00006] SYNC FIND: sf_idx=0, ret=0, next_state=0
12:28:28.901055 [PHY0] [I] [00006] CP-CFO: estimated=-0.026722,
mean=0.003309
12:28:28.901240 [PHY0] [I] [00006] PSS: id=0, peak_pos=5062,
peak_value=1.013647
12:28:28.901245 [PHY0] [I] [00006] SYNC FIND: sf_idx=0, ret=0, next_state=0
12:28:28.901299 [PHY0] [I] [00006] CP-CFO: estimated=-0.042037,
mean=-0.001225
12:28:28.901477 [PHY0] [I] [00006] PSS: id=0, peak_pos=5062,
peak_value=1.010350
12:28:28.901481 [PHY0] [I] [00006] SYNC FIND: sf_idx=0, ret=0, next_state=0
12:28:28.901535 [PHY0] [I] [00006] CP-CFO: estimated=-0.059047,
mean=-0.007008
12:28:28.901716 [PHY0] [I] [00006] PSS: id=0, peak_pos=5062,
peak_value=1.006251
12:28:28.901720 [PHY0] [I] [00006] SYNC FIND: sf_idx=0, ret=0, next_state=0
12:28:28.905953 [PHY0] [I] [00006] CP-CFO: estimated=-0.017377,
mean=-0.008045
12:28:28.906152 [PHY0] [I] [00006] PSS: id=0, peak_pos=598,
peak_value=1.077479
12:28:28.906158 [PHY0] [I] [00006] SYNC FIND: sf_idx=0, ret=0, next_state=0
12:28:28.911242 [PHY0] [I] [00006] CP-CFO: estimated=-0.014781,
mean=-0.008718
12:28:28.911436 [PHY0] [I] [00006] PSS: id=0, peak_pos=533,
peak_value=1.007110
12:28:28.911441 [PHY0] [I] [00006] SYNC FIND: sf_idx=0, ret=0, next_state=0
12:28:28.916005 [PHY0] [I] [00006] CP-CFO: estimated=-0.013738,
mean=-0.009220
12:28:28.916191 [PHY0] [I] [00006] PSS: id=0, peak_pos=598,
peak_value=1.061546
12:28:28.916196 [PHY0] [I] [00006] SYNC FIND: sf_idx=0, ret=0, next_state=0
12:28:28.921291 [PHY0] [I] [00006] CP-CFO: estimated=-0.001139,
mean=-0.008412
12:28:28.921480 [PHY0] [I] [00006] PSS: id=0, peak_pos=768,
peak_value=1.180098
12:28:28.921485 [PHY0] [I] [00006] SYNC FIND: sf_idx=0, ret=0, next_state=0
12:28:28.926029 [PHY0] [I] [00006] CP-CFO: estimated=-0.002084,
mean=-0.002084
12:28:28.926230 [PHY0] [I] [00006] PSS: id=1, peak_pos=697,
peak_value=4.826238
12:28:28.926239 [PHY0] [I] [00006] PSS-CFO: filter=yes,
estimated=-0.001127, mean=-0.001127
12:28:28.926246 [PHY0] [I] [00006] SSS detected N_id_1=0, sf_idx=0,
Normal CP
12:28:28.926250 [PHY0] [I] [00006] SSS detected N_id_1=0, sf_idx=5,
Normal CP
12:28:28.926257 [PHY0] [I] [00006] SYNC FIND: sf_idx=5, ret=1, next_state=0
12:28:28.931358 [PHY0] [I] [00006] CP-CFO: estimated=-0.011828,
mean=-0.003058
12:28:28.931567 [PHY0] [I] [00006] PSS: id=1, peak_pos=697,
peak_value=6.350407
12:28:28.931574 [PHY0] [I] [00006] PSS-CFO: filter=yes,
estimated=0.008584, mean=-0.000156
12:28:28.931581 [PHY0] [I] [00006] SSS detected N_id_1=0, sf_idx=5,
Normal CP
12:28:28.931586 [PHY0] [I] [00006] SSS detected N_id_1=0, sf_idx=0,
Normal CP
12:28:28.931593 [PHY0] [I] [00006] SYNC FIND: sf_idx=0, ret=1, next_state=0
12:28:28.936093 [PHY0] [I] [00006] CP-CFO: estimated=-0.011870,
mean=-0.003939
12:28:28.936312 [PHY0] [I] [00006] PSS: id=1, peak_pos=697,
peak_value=5.772885
12:28:28.936319 [PHY0] [I] [00006] PSS-CFO: filter=yes,
estimated=0.010786, mean=0.000939
12:28:28.936326 [PHY0] [I] [00006] SSS detected N_id_1=0, sf_idx=0,
Normal CP
12:28:28.936332 [PHY0] [I] [00006] SSS detected N_id_1=154, sf_idx=5,
Normal CP
12:28:28.936339 [PHY0] [I] [00006] SYNC FIND: sf_idx=5, ret=1, next_state=0
12:28:28.941390 [PHY0] [I] [00006] CP-CFO: estimated=-0.005995,
mean=-0.004145
12:28:28.941644 [PHY0] [I] [00006] PSS: id=1, peak_pos=697,
peak_value=9.593502
12:28:28.941653 [PHY0] [I] [00006] PSS-CFO: filter=yes,
estimated=-0.014034, mean=-0.000559
12:28:28.941661 [PHY0] [I] [00006] SSS detected N_id_1=0, sf_idx=5,
Normal CP
12:28:28.941677 [PHY0] [I] [00006] SSS detected N_id_1=0, sf_idx=0,
Normal CP
12:28:28.941686 [PHY0] [I] [00006] SYNC FIND: sf_idx=0, ret=1, next_state=0
12:28:28.946194 [PHY0] [I] [00006] CP-CFO: estimated=-0.011962,
mean=-0.011962
12:28:28.946453 [PHY0] [I] [00006] PSS: id=2, peak_pos=721,
peak_value=1.073463
12:28:28.946460 [PHY0] [I] [00006] SYNC FIND: sf_idx=0, ret=0, next_state=0
12:28:28.950980 [PHY0] [I] [00006] CP-CFO: estimated=0.001869,
mean=-0.010579
12:28:28.951264 [PHY0] [I] [00006] PSS: id=2, peak_pos=730,
peak_value=1.196660
12:28:28.951271 [PHY0] [I] [00006] SYNC FIND: sf_idx=0, ret=0, next_state=0
12:28:28.956239 [PHY0] [I] [00006] CP-CFO: estimated=-0.008045,
mean=-0.010325
12:28:28.956569 [PHY0] [I] [00006] PSS: id=2, peak_pos=847,
peak_value=1.102638
12:28:28.956578 [PHY0] [I] [00006] SYNC FIND: sf_idx=0, ret=0, next_state=0
12:28:28.961022 [PHY0] [I] [00006] CP-CFO: estimated=0.000635,
mean=-0.009229
12:28:28.961379 [PHY0] [I] [00006] PSS: id=2, peak_pos=636,
peak_value=1.049430
12:28:28.961389 [PHY0] [I] [00006] SYNC FIND: sf_idx=0, ret=0, next_state=0
12:28:28.966361 [PHY0] [I] [00006] CP-CFO: estimated=-0.020372,
mean=-0.010344
12:28:28.966779 [PHY0] [I] [00006] PSS: id=2, peak_pos=730,
peak_value=1.038419
12:28:28.966802 [PHY0] [I] [00006] SYNC FIND: sf_idx=0, ret=0, next_state=0
12:28:28.971109 [PHY0] [I] [00006] CP-CFO: estimated=-0.006383,
mean=-0.009948
12:28:28.971604 [PHY0] [I] [00006] PSS: id=2, peak_pos=730,
peak_value=1.106085
12:28:28.971620 [PHY0] [I] [00006] SYNC FIND: sf_idx=0, ret=0, next_state=0
12:28:28.976482 [PHY0] [I] [00006] CP-CFO: estimated=-0.009273,
mean=-0.009880
12:28:28.977087 [PHY0] [I] [00006] PSS: id=2, peak_pos=789,
peak_value=1.095910
12:28:28.977108 [PHY0] [I] [00006] SYNC FIND: sf_idx=0, ret=0, next_state=0
12:28:28.981259 [PHY0] [I] [00006] CP-CFO: estimated=-0.003089,
mean=-0.009201
12:28:28.982025 [PHY0] [I] [00006] PSS: id=2, peak_pos=730,
peak_value=1.022967
12:28:28.982049 [PHY0] [I] [00006] SYNC FIND: sf_idx=0, ret=0, next_state=0
12:28:28.982081 [PHY0] [I] [00006] SYNC: PSS/SSS detected: Mode=FDD,
PCI=1, CFO=-0.1 KHz, CP=Normal
12:28:28.983281 [PHY0] [I] [00006] Generated SSS for N_id_1=0, cell_id=1
12:28:28.983371 [PHY0] [I] [00006] PSS: id=1, peak_pos=697,
peak_value=7.008056
12:28:28.983394 [PHY0] [I] [00006] PSS-CFO: filter=yes,
estimated=0.010289, mean=0.010289
12:28:28.983422 [PHY0] [I] [00006] SSS correlation with N_id_1=0,
sf0=148060.44, sf5=9479.08, sf_idx=0, ratio=15.6
12:28:28.983448 [PHY0] [I] [00006] Realigning frame, reading 1657 samples
12:28:28.983497 [PHY0] [I] [00006] SYNC FIND: sf_idx=1, ret=0, next_state=1
12:28:28.984230 [PHY0] [I] [00006] SYNC TRACK: sf_idx=2, ret=1,
next_state=1
12:28:28.984759 [PHY0] [I] [00006] SYNC TRACK: sf_idx=3, ret=1,
next_state=1
12:28:28.985805 [PHY0] [I] [00006] SYNC TRACK: sf_idx=4, ret=1,
next_state=1
12:28:28.986903 [PHY0] [I] [00006] AGC gain: 0.00 (17.00) y_out=1.145,
y=1.065 target=0.3
12:28:28.986945 [PHY0] [I] [00006] PSS: id=1, peak_pos=144,
peak_value=17.175945
12:28:28.986969 [PHY0] [I] [00006] PSS-CFO: filter=yes,
estimated=-0.011552, mean=-0.011552
12:28:28.986990 [PHY0] [I] [00006] TRACK: cfo_current=-70.550774,
cfo_strack=-173.273300
12:28:28.987001 [PHY0] [I] [00006] SYNC TRACK: sf_idx=5, ret=1,
next_state=1
12:28:28.987928 [PHY0] [I] [00006] SYNC TRACK: sf_idx=6, ret=1,
next_state=1
12:28:28.988988 [PHY0] [I] [00006] SYNC TRACK: sf_idx=7, ret=1,
next_state=1
12:28:28.990045 [PHY0] [I] [00006] SYNC TRACK: sf_idx=8, ret=1,
next_state=1
12:28:28.991099 [PHY0] [I] [00006] SYNC TRACK: sf_idx=9, ret=1,
next_state=1
12:28:28.992179 [PHY0] [I] [00006] PSS: id=1, peak_pos=144,
peak_value=15.850657
12:28:28.992207 [PHY0] [I] [00006] PSS-CFO: filter=yes,
estimated=-0.011007, mean=-0.011524
12:28:28.992228 [PHY0] [I] [00006] TRACK: cfo_current=-70.550774,
cfo_strack=-172.865128
12:28:28.992239 [PHY0] [I] [00006] SYNC TRACK: sf_idx=0, ret=1,
next_state=1
12:28:28.993012 [PHY0] [I] [00006] Decoded PBCH: src=0, dst=3, nb=1,
sfn_offset=3
12:28:28.993044 [PHY0] [I] [00006] MIB decoded: 0
12:28:28.993091 [PHY0] [I] [00006] SYNC: MIB Decoded: Mode=FDD, PCI=1,
PRB=15, Ports=2, CFO=-0.1 KHz
12:28:28.994913 [PHY0] [I] [00010] Generated SSS for N_id_1=0, cell_id=1
12:28:28.995618 [PHY0] [I] [00010] Indexing 120 REGs. CellId: 1, 15
PRB, CP: Normal
12:28:28.995655 [PHY0] [I] [00010] PCFICH allocating 4 regs. CellID: 1,
PRB: 15
12:28:28.995680 [PHY0] [I] [00010] Creating 1 PHICH mapping units.
Normal length, Ng=0.17
12:28:28.995699 [PHY0] [I] [00010] Init PDCCH REG space CFI 1. 18
useful REGs (2 CCEs)
12:28:28.995713 [PHY0] [I] [00010] Init PDCCH REG space CFI 2. 63
useful REGs (7 CCEs)
12:28:28.995731 [PHY0] [I] [00010] Init PDCCH REG space CFI 3. 108
useful REGs (12 CCEs)
12:28:28.996604 [PHY0] [I] [00011] PDCCH: Cell config PCI=0, 0 ports.
12:28:28.996792 [PHY0] [I] [00011] PDSCH: Cell config PCI=1, 2 ports,
15 PRBs, max_symbols: 2520
12:28:28.996809 [PHY0] [I] [00011] PMCH: Cell config PCI=2, 1 ports, 15
PRBs, max_symbols: 2160
12:28:29.002717 [PHY0] [I] [00017] Indexing 120 REGs. CellId: 1, 15
PRB, CP: Normal
12:28:29.002756 [PHY0] [I] [00018] PCFICH allocating 4 regs. CellID: 1,
PRB: 15
12:28:29.002785 [PHY0] [I] [00018] Creating 1 PHICH mapping units.
Normal length, Ng=0.17
12:28:29.002825 [PHY0] [I] [00018] Init PDCCH REG space CFI 1. 18
useful REGs (2 CCEs)
12:28:29.002842 [PHY0] [I] [00018] Init PDCCH REG space CFI 2. 63
useful REGs (7 CCEs)
12:28:29.002915 [PHY0] [I] [00018] Init PDCCH REG space CFI 3. 108
useful REGs (12 CCEs)
12:28:29.003651 [PHY0] [I] [00018] PDCCH: Cell config PCI=0, 0 ports.
12:28:29.003895 [PHY0] [I] [00019] PDSCH: Cell config PCI=1, 2 ports,
15 PRBs, max_symbols: 2520
12:28:29.003914 [PHY0] [I] [00019] PMCH: Cell config PCI=2, 1 ports, 15
PRBs, max_symbols: 2160
12:28:29.009609 [PHY0] [I] [00024] Indexing 120 REGs. CellId: 1, 15
PRB, CP: Normal
12:28:29.009645 [PHY0] [I] [00024] PCFICH allocating 4 regs. CellID: 1,
PRB: 15
12:28:29.009677 [PHY0] [I] [00024] Creating 1 PHICH mapping units.
Normal length, Ng=0.17
12:28:29.009698 [PHY0] [I] [00024] Init PDCCH REG space CFI 1. 18
useful REGs (2 CCEs)
12:28:29.009712 [PHY0] [I] [00024] Init PDCCH REG space CFI 2. 63
useful REGs (7 CCEs)
12:28:29.009728 [PHY0] [I] [00024] Init PDCCH REG space CFI 3. 108
useful REGs (12 CCEs)
12:28:29.010613 [PHY0] [I] [00025] PDCCH: Cell config PCI=0, 0 ports.
12:28:29.010816 [PHY0] [I] [00025] PDSCH: Cell config PCI=1, 2 ports,
15 PRBs, max_symbols: 2520
12:28:29.010840 [PHY0] [I] [00025] PMCH: Cell config PCI=2, 1 ports, 15
PRBs, max_symbols: 2160
12:28:29.016338 [PHY0] [I] [00031] Cell Search: Setting sampling rate
and synchronizing SFN...
12:28:29.016358 [PHY0] [I] [00031] SYNC: Setting sampling rate 3.84 MHz
12:28:29.880667 [MAC ] [I] [00031] DL retx: 0.00 %, perpkt: 0.00, UL
retx: 0.00 % perpkt: 0.00
12:28:29.880731 [RLC ] [I] LCID=0, RX throughput: 0.000000 Mbps. TX
throughput: 0.000000 Mbps.
12:28:29.880755 [GW ] [I] RX throughput: 0.000000 Mbps. TX throughput:
0.000000 Mbps.
12:28:30.880669 [MAC ] [I] [00031] DL retx: 0.00 %, perpkt: 0.00, UL
retx: 0.00 % perpkt: 0.00
12:28:30.880727 [RLC ] [I] LCID=0, RX throughput: 0.000000 Mbps. TX
throughput: 0.000000 Mbps.
12:28:30.880748 [GW ] [I] RX throughput: 0.000000 Mbps. TX throughput:
0.000000 Mbps.
12:28:31.016468 [PHY0] [E] [00031] RX failed: Operation timed out
12:28:31.880672 [MAC ] [I] [00032] DL retx: 0.00 %, perpkt: 0.00, UL
retx: 0.00 % perpkt: 0.00
12:28:31.880730 [RLC ] [I] LCID=0, RX throughput: 0.000000 Mbps. TX
throughput: 0.000000 Mbps.
12:28:31.880749 [GW ] [I] RX throughput: 0.000000 Mbps. TX throughput:
0.000000 Mbps.
12:28:32.880666 [MAC ] [I] [00032] DL retx: 0.00 %, perpkt: 0.00, UL
retx: 0.00 % perpkt: 0.00
12:28:32.880722 [RLC ] [I] LCID=0, RX throughput: 0.000000 Mbps. TX
throughput: 0.000000 Mbps.
12:28:32.880740 [GW ] [I] RX throughput: 0.000000 Mbps. TX throughput:
0.000000 Mbps.
12:28:33.016664 [PHY0] [E] [00032] RX failed: Operation timed out
12:28:33.016717 [PHY0] [E] [00032] Error receiving samples
12:28:33.016736 [PHY0] [E] [00032] SYNC: Error calling ue_sync_get_buffer.
12:28:33.016814 [PHY0] [I] [00034] Cell Search: Could not synchronize
with cell
12:28:33.016863 [PHY0] [I] [00037] Cell Search: No more frequencies in
the current EARFCN set
12:28:33.016909 [RRC ] [I] No cells found.
12:28:33.016921 [NAS ] [W] Did not find any PLMN in the set of frequencies
12:28:33.880666 [MAC ] [I] [00093] DL retx: 0.00 %, perpkt: 0.00, UL
retx: 0.00 % perpkt: 0.00
12:28:33.880728 [RLC ] [I] LCID=0, RX throughput: 0.000000 Mbps. TX
throughput: 0.000000 Mbps.
12:28:33.880746 [GW ] [I] RX throughput: 0.000000 Mbps. TX throughput:
0.000000 Mbps.
12:28:34.017043 [NAS ] [I] Attach Request
12:28:34.017088 [NAS ] [I] No PLMN selected. Starting PLMN Search...
12:28:34.017106 [RRC ] [I] Starting PLMN search
12:28:34.880667 [MAC ] [I] [00093] DL retx: 0.00 %, perpkt: 0.00, UL
retx: 0.00 % perpkt: 0.00
12:28:34.880729 [RLC ] [I] LCID=0, RX throughput: 0.000000 Mbps. TX
throughput: 0.000000 Mbps.
12:28:34.880746 [GW ] [I] RX throughput: 0.000000 Mbps. TX throughput:
0.000000 Mbps.
12:28:35.017787 [PHY0] [E] [00093] RX failed: Operation timed out
12:28:35.017881 [PHY0] [I] [00094] Cell Search: Start EARFCN index=0/1
12:28:35.017986 [PHY0] [I] [00098] Cell Search: Setting Cell search state
12:28:35.032078 [PHY0] [I] [00101] SYNC: Setting Cell Search sampling rate
12:28:35.032128 [PHY0] [I] [00101] SYNC: Searching for cell...
More information about the srsran-users
mailing list