[srslte-users] srsUE 20.04.1: Can't open RF frontend (NI USRP 2944 with UHD FPGA Image) - Error: Radio does not provide RF information / Error opening UHD: code 43
Xavier Arteaga
xavier at softwareradiosystems.com
Tue Jun 2 08:03:04 UTC 2020
Hi Marc,
When RF device arguments are set, the device type needs to be specified.
Otherwise, it picks the default master clock rate for AD9361 based devices
(B200). This will be improved in the next release.
Could you try adding type=x300 to the device args parameters? Also, you can
specify the master clock rate as well.
[rf]
device_args =
type=x300,master_clock_rate=184.32e6,recv_frame_size=9232,send_frame_size=9232
Kind regards,
Xavier
On Tue, 2 Jun 2020 at 09:26, Marc T. <m.triefelder at gmail.com> wrote:
> HI srsLTE Team and Community,
>
> i have the issue srsUE can’t open my USRP 2944 (160MHz version). For sure
> i flashed there UHD Image on it. the 2944 is based on the Ettus x310 board,
> which should be supported actually…
> When i check the device from the console with the uhd_* commands ever this
> seems to be fine.
>
> But in the ue.log i can see the issue „Error: Radio does not provide RF
> information“ - Any Idea how to proceed in this case?
>
>
> Thank you very much in advance,
> Marc
>
> Here some infos:
>
>
> sml at sml-hp-b65a:~$ uhd_find_devices
>
> [INFO] [UHD] linux; GNU C++ version 7.4.0; Boost_106501;
> UHD_3.14.1.1-release
>
> --------------------------------------------------
>
> -- UHD Device 0
>
> --------------------------------------------------
>
> Device Address:
>
> serial: 31A3xxx
>
> addr: 192.168.10.2
>
> fpga: HG
>
> name:
>
> product: X310
>
> type: x300
>
>
>
>
>
> sml at sml-hp-b65a:~$ uhd_usrp_probe
>
> [INFO] [UHD] linux; GNU C++ version 7.4.0; Boost_106501;
> UHD_3.14.1.1-release
>
> [INFO] [X300] X300 initialization sequence...
>
> [INFO] [X300] Maximum frame size: 1472 bytes.
>
> [INFO] [X300] Radio 1x clock: 200 MHz
>
> [INFO] [0/DmaFIFO_0] Initializing block control (NOC ID:
> 0xF1F0D00000000000)
>
> [INFO] [0/DmaFIFO_0] BIST passed (Throughput: 1302 MB/s)
>
> [INFO] [0/DmaFIFO_0] BIST passed (Throughput: 1302 MB/s)
>
> [INFO] [0/Radio_0] Initializing block control (NOC ID: 0x12AD100000000001)
>
> [INFO] [0/Radio_1] Initializing block control (NOC ID: 0x12AD100000000001)
>
> [INFO] [0/DDC_0] Initializing block control (NOC ID: 0xDDC0000000000000)
>
> [INFO] [0/DDC_1] Initializing block control (NOC ID: 0xDDC0000000000000)
>
> [INFO] [0/DUC_0] Initializing block control (NOC ID: 0xD0C0000000000000)
>
> [INFO] [0/DUC_1] Initializing block control (NOC ID: 0xD0C0000000000000)
>
> _____________________________________________________
>
> /
>
> | Device: X-Series Device
>
> | _____________________________________________________
>
> | /
>
> | | Mboard: X310
>
> | | revision: 11
>
> | | revision_compat: 7
>
> | | product: 30806
>
> | | mac-addr0: 00:80:2f:26:a4:f5
>
> | | mac-addr1: 00:80:2f:26:a4:f6
>
> | | gateway: 192.168.10.1
>
> | | ip-addr0: 192.168.10.2
>
> | | subnet0: 255.255.255.0
>
> | | ip-addr1: 192.168.20.2
>
> | | subnet1: 255.255.255.0
>
> | | ip-addr2: 192.168.30.2
>
> | | subnet2: 255.255.255.0
>
> | | ip-addr3: 192.168.40.2
>
> | | subnet3: 255.255.255.0
>
> | | serial: 31A3xxx
>
> | | FW Version: 6.0
>
> | | FPGA Version: 35.1
>
> | | FPGA git hash: bb85bdf
>
> | | RFNoC capable: Yes
>
> | |
>
> | | Time sources: internal, external, gpsdo
>
> | | Clock sources: internal, external, gpsdo
>
> | | Sensors: ref_locked
>
> | | _____________________________________________________
>
> | | /
>
> | | | RX Dboard: A
>
> | | | ID: UBX-160 v1 (0x007a)
>
> | | | Serial: 31A0xxx
>
> | | | _____________________________________________________
>
> | | | /
>
> | | | | RX Frontend: 0
>
> | | | | Name: UBX RX
>
> | | | | Antennas: TX/RX, RX2, CAL
>
> | | | | Sensors: lo_locked
>
> | | | | Freq range: 10.000 to 6000.000 MHz
>
> | | | | Gain range PGA0: 0.0 to 31.5 step 0.5 dB
>
> | | | | Bandwidth range: 160000000.0 to 160000000.0 step 0.0 Hz
>
> | | | | Connection Type: IQ
>
> | | | | Uses LO offset: No
>
> | | | _____________________________________________________
>
> | | | /
>
> | | | | RX Codec: A
>
> | | | | Name: ads62p48
>
> | | | | Gain range digital: 0.0 to 6.0 step 0.5 dB
>
> | | _____________________________________________________
>
> | | /
>
> | | | RX Dboard: B
>
> | | | ID: UBX-160 v1 (0x007a)
>
> | | | Serial: 31A0xxx
>
> | | | _____________________________________________________
>
> | | | /
>
> | | | | RX Frontend: 0
>
> | | | | Name: UBX RX
>
> | | | | Antennas: TX/RX, RX2, CAL
>
> | | | | Sensors: lo_locked
>
> | | | | Freq range: 10.000 to 6000.000 MHz
>
> | | | | Gain range PGA0: 0.0 to 31.5 step 0.5 dB
>
> | | | | Bandwidth range: 160000000.0 to 160000000.0 step 0.0 Hz
>
> | | | | Connection Type: IQ
>
> | | | | Uses LO offset: No
>
> | | | _____________________________________________________
>
> | | | /
>
> | | | | RX Codec: B
>
> | | | | Name: ads62p48
>
> | | | | Gain range digital: 0.0 to 6.0 step 0.5 dB
>
> | | _____________________________________________________
>
> | | /
>
> | | | TX Dboard: A
>
> | | | ID: UBX-160 v1 (0x0079)
>
> | | | Serial: 31A0xxx
>
> | | | _____________________________________________________
>
> | | | /
>
> | | | | TX Frontend: 0
>
> | | | | Name: UBX TX
>
> | | | | Antennas: TX/RX, CAL
>
> | | | | Sensors: lo_locked
>
> | | | | Freq range: 10.000 to 6000.000 MHz
>
> | | | | Gain range PGA0: 0.0 to 31.5 step 0.5 dB
>
> | | | | Bandwidth range: 160000000.0 to 160000000.0 step 0.0 Hz
>
> | | | | Connection Type: QI
>
> | | | | Uses LO offset: No
>
> | | | _____________________________________________________
>
> | | | /
>
> | | | | TX Codec: A
>
> | | | | Name: ad9146
>
> | | | | Gain Elements: None
>
> | | _____________________________________________________
>
> | | /
>
> | | | TX Dboard: B
>
> | | | ID: UBX-160 v1 (0x0079)
>
> | | | Serial: 31A0xxx
>
> | | | _____________________________________________________
>
> | | | /
>
> | | | | TX Frontend: 0
>
> | | | | Name: UBX TX
>
> | | | | Antennas: TX/RX, CAL
>
> | | | | Sensors: lo_locked
>
> | | | | Freq range: 10.000 to 6000.000 MHz
>
> | | | | Gain range PGA0: 0.0 to 31.5 step 0.5 dB
>
> | | | | Bandwidth range: 160000000.0 to 160000000.0 step 0.0 Hz
>
> | | | | Connection Type: QI
>
> | | | | Uses LO offset: No
>
> | | | _____________________________________________________
>
> | | | /
>
> | | | | TX Codec: B
>
> | | | | Name: ad9146
>
> | | | | Gain Elements: None
>
> | | _____________________________________________________
>
> | | /
>
> | | | RFNoC blocks on this device:
>
> | | |
>
> | | | * DmaFIFO_0
>
> | | | * Radio_0
>
> | | | * Radio_1
>
> | | | * DDC_0
>
> | | | * DDC_1
>
> | | | * DUC_0
>
> | | | * DUC_1
>
>
>
> sml at sml-hp-b65a:~$
>
>
> Here an except from the ue.log:
>
> sml at sml-hp-b65a:~$ cat /tmp/ue.log
>
> 07:59:45.629027 [UE ] [I] Built in Release mode using commit c892ae56b on
> branch master.
>
> 07:59:45.706804 [RF ] [I] Configuring physical DL channel 0 with
> band-pass filter (0.0, 0.0)
>
> 07:59:45.706818 [RF ] [I] Configuring physical UL channel 0 with
> band-pass filter (0.0, 0.0)
>
> 07:59:47.386876 [RF ] [E] Error opening RF device
>
> 07:59:47.500038 [MAC ] [I] [ 0] Resetting MAC
>
> 07:59:47.503034 [MAC ] [D] [ 0] Msg3 buffer flushed
>
> 07:59:47.503049 [MAC ] [I] [ 0] Logical Channel Setup: LCID=0, LCG=0,
> priority=0, PBR=-1, BSD=50ms, bucket_size=0
>
> 07:59:47.503054 [MAC ] [I] [ 0] Logical Channel Setup: LCID=1, LCG=0,
> priority=1, PBR=-1, BSD=50ms, bucket_size=0
>
> 07:59:47.503062 [MAC ] [D] [ 0] After MAC reset:
>
> - lcid=0, lcg=0, prio=0, Bj=0, PBR=-1, BSD=50, buffer_len=0, sched_len=0
>
> - lcid=1, lcg=0, prio=1, Bj=0, PBR=-1, BSD=50, buffer_len=0, sched_len=0
>
> 07:59:47.503064 [MAC ] [I] [ 0] BSR: Configured timer reTX 2560 ms
>
> 07:59:47.503071 [RLC ] [I] Added radio bearer SRB0 in Transparent Mode
>
> 07:59:47.503072 [RLC ] [I] Configured radio bearer SRB0 in Transparent Mode
>
> 07:59:47.503075 [NAS ] [I] New state DEREGISTERED
>
> 07:59:47.503108 [USIM] [I] Read Home PLMN Id=26222
>
> 07:59:47.503172 [NAS ] [I] Read GUTI from file m_tmsi: d0c2ac97, mcc: 106,
> mnc: 16, mme_group_id: 1, mme_code: 1
>
> 07:59:47.503180 [NAS ] [I] Read security ctxt from file .ctxt. ksi: 1,
> k_asme: 392be0dcb559e2f54159362e8dcd58e75e02b24e1eceb77d55a576088bc37e1c,
> tx_count: 4, rx_count: 4, int_alg: 2, enc_alg: 0
>
> 07:59:47.503190 [NAS ] [D] NAS encryption key - k_nas_enc
>
> 0000: 97 80 a3 41 25 d8 57 0e f1 ca f7 06 5c 23 1b 74
>
> 0010: 12 b0 f2 6b ed e2 62 e2 ae bb 72 12 93 12 59 29
>
> 07:59:47.503195 [NAS ] [D] NAS integrity key - k_nas_int
>
> 0000: f9 78 39 58 42 5f d5 f6 05 d7 dc 9a 02 33 23 f7
>
> 0010: 4d 40 56 d4 38 8d 19 37 0d fa 52 98 08 4f 9e f7
>
> 07:59:47.503205 [RRC ] [I] using srand seed of 503204
>
> 07:59:48.034353 [PHY0] [E] [ 0] Error: Radio does not provide RF
> information
>
> 07:59:48.040594 [PHY0] [D] [ 0] SYNC: state=IDLE, tti=0
>
> 07:59:48.040605 [PHY0] [D] [ 0] Sleeping
>
> 07:59:48.040691 [NAS ] [I] Saved GUTI to file m_tmsi: d0c2ac97, mcc: 106,
> mnc: 16, mme_group_id: 1, mme_code: 1
>
> 07:59:48.040703 [NAS ] [I] Saved security ctxt to file .ctxt. ksi: 1,
> k_asme: 392be0dcb559e2f54159362e8dcd58e75e02b24e1eceb77d55a576088bc37e1c,
> tx_count: 4, rx_count: 4, int_alg: 2, enc_alg: 0
>
> 07:59:48.040756 [MAC ] [D] [ 0] Running MAC tti=0
>
> 07:59:48.040761 [MAC ] [D] [ 0] Update Bj: lcid=0, Bj=0
>
> 07:59:48.040763 [MAC ] [D] [ 0] Update Bj: lcid=1, Bj=0
>
> 07:59:48.040768 [MAC ] [D] [ 0] RA: INIT: rar_window_start=-1,
> rar_window_length=-1
>
> 07:59:48.041618 [PHY0] [D] [ 0] SYNC: state=IDLE, tti=1
>
> 07:59:48.041626 [PHY0] [D] [ 0] Sleeping
>
> Closing log
>
> sml at sml-hp-b65a:~$
>
>
>
> Here is how it looks if i try to start srsue:
>
> sml at sml-hp-b65a:~$ sudo ./srsue20.04.1 ue-v20.04-Xavier-VPN-Sky5-UHD.conf
>
> Reading configuration file ue-v20.04-Xavier-VPN-Sky5-UHD.conf...
>
>
>
> Built in Release mode using commit c892ae56b on branch master.
>
>
>
> Opening 2 channels in RF device=UHD with
> args=recv_frame_size=9232,send_frame_size=9232
>
> [INFO] [UHD] linux; GNU C++ version 7.4.0; Boost_106501;
> UHD_3.14.1.1-release
>
> [INFO] [LOGGING] Fastpath logging disabled at runtime.
>
> Opening USRP channels=2,
> args: recv_frame_size=9232,send_frame_size=9232,master_clock_rate=23.04e6
>
> [INFO] [X300] X300 initialization sequence...
>
> /home/sml/srsLTE/lib/src/phy/rf/rf_uhd_imp.c.187: Error opening UHD: code
> 43
>
>
>
> Error initializing radio.
>
> Waiting PHY to initialize ... done!
>
> Saving MAC PCAP file
>
> Saving NAS PCAP file (DLT=148)
>
> sml at sml-hp-b65a:~$
>
>
> Mit freundlichen Grüßen,
> Best regards,
>
> Marc Triefelder
>
> E-Mail: m.triefelder at gmail.com
>
>
>
>
>
> _______________________________________________
> srslte-users mailing list
> srslte-users at lists.softwareradiosystems.com
> http://www.softwareradiosystems.com/mailman/listinfo/srslte-users
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://lists.srsran.com/pipermail/srsran-users/attachments/20200602/cbe5f3e9/attachment.htm>
More information about the srsran-users
mailing list